Proizvodi

Model: ACO-T602
Related Standards: ISO 2592, ASTM D92, IP 36, etc.
Measuring Range: Ambient to 400°C
Test Mode: ASTM D92 Flash, Flash + Fire, Fire point must be visually monitored
Display: Fluorescent display tube (VFD module)
Printer: Thermal type printer (provided)
Temperatur Sensor: PT-100 in stainless steel sheath
Flash Detection: Ionization between test cup and igniters (Patented)
Heater: Nichrome Coil heater: 1kW@100V or 1.2kW@220V
Ignition Source: Dual Electric Igniters (platinum coil)
Cooling Device: Forced air cooling by sirocco fan
Barometric Correction: By built-in barometric pressure sensor
Data Output: RS-232C 1 channel
Safety Mechanism: Fire containment lid which activates automatically to help putting out fire when ACO-T602 detects a specimen is burning up heavily. If flash is not detected until the temperature reaches EFP+30 oC or 400 oC, the test is terminated and cooling starts. Automatically shuts off and the problem is reported by buzzer and display, in case: (a) Temperature sensor is found defective, (b) Flash detector is found defective, (c) Thermofuse is blown (Also fire containment lid activates), (d) Built-in battery is found drained out, (e) Upper arm switch is found defective, (f) Lower arm switch is found defective, (g) Shutter open/close switch is found defective, or (h) Control computer runs away (no display)
Dimension & Weight: Control unit: 230W x 455D x 110H (mm), 6kg; Test unit: 405W x 515D x 400H (mm), 33kg; Printer: 134W x 180D x 58H (mm), 0.6kg
Installation Site: Ambient temperature: 0 to 40 oC; RH: Less than 90% (no condensation)
Power Supply: Single Phase AC100/120V or 220/240V 50/60Hz, (set at the factory) 1.7kW(max.), One line must be grounded.

IQ/OQ/PQ Qualification: Yes, possible

Model: MPC-102L
Type:: Mini Pour Point(PP) and Cloud Point(CP) tester with sequential CP and PP measuring capability. Sample cooling and pre-heating by TED.
Test Standards: ASTM D6749/D97, ISO 3016 (PP), ASTM D7683/D2500, ISO 3015 (CP)
Specimen Volume: 4.5ml
Cooling: Liquid Cooling
Measuring Range: -40°C to +51°C with tap water of 20°C; -65°C to +51°C with cooling liquid of -35°C (*:Sample viscosity, etc. affects on lowest temperature of the measuring range.)
Measurement Modes: Selectable from various modes. 1.CP mode (0.1 or 1.0 °C, selectable) 2.PP modes: Programmed by the user. Programmable parameters are: *Amount of applied air pressure for PP detection, to accommodate different sample types: L(low) for diesel fuels, H(high) for lube oils, VH(very high) and UH (ultra high) for residual fuels and similar samples. *Testing intervals: 1.0°C, 2.5°C, or 3.0°C (In total, 4x3=12 modes for PP.) 3.CP/PP modes: CP is determined and then PP. PP detection is programmable by the user with the same parameters as PP modes'. (12 modes in total.)
Sample Automatic Pre-Heating: Automatic preheating at either +45°C or EPP+10°C. (EPP=Expected Pour Point)
Display: Test parameters, EPP, bath temperature, sample temperature, PP, and CP displayed on VFD. Temperatures displayed in 0.1°C increments.
EPP Setting: EPP (Expected Pour Point) needs to be set prior to test starts.
Specimen Cup: Cylindrical glass test jar with 4.5ml sample volume.
Sensors: Compound type sensor assembly for PP and CP. PP detected by air pressure method (patented). CP detected photo-electrically. Pt100 temperature sensors.
Sample Cooling Rate: As standard, 4°C/min. till EPP+40°C, and 1°C/min. Thereafter, cooling profile is programmable.
Safety Shutdown: As hot side of TED reaches 60°C while preheating, warning buzzer beeps and heating stops.
Data Output: RS-232C 1 channel (for PC or Optional Printer)
Data Strage: Last 50 test data are stored in RAM
Power Requirements: 100, 120, 220, or 240VAC 0.5kW
Dimensions (WxDxH) (mm) and Weight: 230mm x 480 x 385, 20kg

IQ/OQ/PQ Qualification: Yes, possible

Model: APM-8 / APM-8FC
Test Methods: ISO 2719, ASTM D93, IP34 JIS K2265-3
Measuring Range: Ambient to 370°C
Ignition source: Gas flame or Electric Coil
Temperature Sensor: PT-100 in stainless steel sheath
Flash Detector: CRC Thermocouple
Power consumption: 720W
Size: 230(W) x 470(D) x 385(H) mm
Net Weight: 17kg

IQ/OQ/PQ kvalifikacija: Yes, possible

Model: AVP-30D2
Related Standards: ISO 3007, ASTM D323, IP69 etc.
Type: Bench-top automated instrument. Automated continuous shaking of test cylinder by "seesaw" motion.
Number Of Cylinders (Measurement Spots): 2
Measuring Range: 0 to 196 kPa (2 kgf/cm2)
Test Cylinders: Small size stainless steel cylinders with 66% in length and 31% in volume compared to the regular full size cylinders. The V/L ratio of 4 is the same as full size cylinder. A "Quick Coupler" is equipped at the center of the vapor cylinder for connecting to external pressure sensor located inside of the tester
Pressure Sensor: Semiconductor type pressure sensor.
Range: 0 to 196 kPa (2kgf/cm2)
Linearity: <0.3% of the range
Hysteresis: <0.3% of the range
Display: LCD with back light
Pressure Display Range: 0 to 200 kPa or 0 to 2 kgf/cm2
Shaking: By "see-saw" movement with angular movement of +/-15 degrees and interval of 6 sec
Bath Temperature Range: Ambient to 60°C
Temp Control: Digital controller/display with PT-100 Sensor, Precision: +/-0.1°C
Stirring: By propeller driven by motor
Heater: Stainless sheathed heater 1.15kW
Calibration: By connecting a Digital Manometer (optional) to the pressure sensor
Safety Mechanism: Water level monitoring device for preventing overheating due to low water level
Data Output: 1xRS-232C channel (for PC or Optional Printer)
Dimension & Weight: 400W x 600D x 720H (mm), 50kg when dry, 85kg when filled with water
Installation Site: Ambient temperature: 0 to 40°C
Relative Humidity: Less than 90% (no condensation)
Power Supply: AC100/120V or 220/240V 50/60Hz (set at the factory) 1.5 kW (max.)

IQ/OQ/PQ Qualification: Yes, possible